Modeling the triceratops
1 Attachment(s)
Hello I am modeling this triceratops. Problem is this that it looks fine in all the view except the front view. Both the legs should be parallel to each other. I have reached to the final stage of my modeling and I don't know how to fix that problem.
Will appreciate if anybody can help solving the problem |
It actully looks correct as it is...
The legs don't need to be totally parallel, remember the hips would be a bit wider then the front as well as the legs being bigger because of more mucsle. If you still want to move it over just select the vertices and start slowing moving it back into the body a bit. |
1 Attachment(s)
Thanks a lot . It makes complete sense what u said.
But i am confused with the reference image i found on the web and also looked some rendred 3d images on the web . So will appreciate if u can look and give me ur feedback. Whether i should move the leg and make it parallel or it looks good the way it is? |
I don't think you need to move the front legs, rather you just need to bow the them out. If you look closely, only appear to line up because the front legs are bowed, kind of like a bulldog's (see link). The picture clearly shows the rear femur to farther out, but rear leg is more linear.
http://www.internal.schools.net.au/e...riceratops.gif If you're still committed to moving the leg, you might consider using a rectangular deformer around the front leg area and scale the deformer vertices out. Could be less of headache then moving vertices individually. |
1 Attachment(s)
Thanks. But I am not aware about how to use rectangular deformer. Can u highlight on that?
This is what it looks in the front view. It seems something is wrong. I don’t know what? |
Sorry, that should have read a lattice deformer. This deformer creates a box around the select model or faces, pulling the lattice points deforms the model the lattice is attached to. Once you have the model deformed to you liking, delete history on it to remove the lattice and keep the deformations.
I still think the top joint of the front legs are fine where they're at. You just need to bow out the front legs to the knees are away from the body. Review the link in my previous reply. |
1 Attachment(s)
Something like this...
|
1 Attachment(s)
Thanks a million.
I did get an idea how it should look. That picture made by view clear and I did what u explained. Here are the results. |
1 Attachment(s)
Suggestions and critique welcome. I have posted by side and front view. Pl let me know if there is anything to improve
|
The head is great! Good body! From the side looks very good, from the front the front legs look... I don't know... rubbery? Too much smoothing maybe?
Again, the head look great smoothed! |
1 Attachment(s)
Thanks. R/ Michael
Here is the front image without smoothing. So what should I do for my legs? Because when i smoothed out the whole model, the legs don't look good. As u mentioned it becomes too much rubbery. What is the solution to it? It will be great if u can suggest me how to overcome this thing. I know exactly how to move the vertices but I am not able to achieve the desired result. I am struggling . so will appreciate ur feedback |
No replies yet. Waiting for some to help me to solve my problem.
Will appreciate help |
Since smoothing basically subdivides that faces, you might manually add more splits to control where the subdivison occur.
You could also manually edit the vetices to compensate for the curvature cause during smooting. Rember the lattice deformer? You could place one around the thigh and manipulate the lattice points to compensate also. I'm sure there are other ways too. |
thanks i did understood what u said but is there any way to select only legs with the deform lattice. i selected the face and clicked on deform lattice but it requires the whole object. So wondering if u know any way that i can only select the front leg after smoothing the whole model
|
Sorry, my mistake. I'm still learning this program too.
You should select the vertices vice the faces then apply the lattice. |
1 Attachment(s)
Looking forward for the feedback!!!!!!!!!!!
image 1 |
1 Attachment(s)
image 2
|
1 Attachment(s)
image 3
|
Cool. Are you going to texture it? That would add a lot.
|
Yes i will
Should i texture in the original version or after smoothing . And should i texture half and then mirror the geometry Will appreciate if u can highlight on the following issue |
I'll defer this to someone with more texturing experience...
|
I think the easiest way to do this is to lay out the UV's of the unsmoothed half, then duplicate the model and combine, flip the UV's and sew them together, and then tweak the UV's to make them fit the smoothed model...
|
Thanks i did get the first part but i am not sure about the second one
flip the UV's and sew them together, and then tweak the UV's to make them fit the smoothed model... It will be great if u can highlight on this futher |
pass by here !prop up
|
All times are GMT. The time now is 07:52 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Simply Maya 2018