SimplyMaya Forums

Welcome to the forum, feel free to ask questions here.


SM Forums / Lounges / Maya Basics & Newbie Lounge / ewbie help adding ik handles to legs, i cant do it

Maya Basics & Newbie Lounge Please post in this section ONLY if your question doesn't fit in anywhere else on the forum, or if you're not sure which section it's relevant to. We also have Free streaming trial available.

Join the conversation. Reply to post
 
Thread Tools
22-01-2005, 09:19 PM   #1
sortedford
Registered User
 
Join Date: Jan 2005
Location: coventry, UK
Posts: 2
ewbie help adding ik handles to legs, i cant do it
these are the instructions i have from my university site, i also have been trying to work from the foundation book 'learning maya 5' (although im using 6.1) each time i can get the skelenton in, add a ik handle, but the knee simply wont bend, the whole leg will rotate no problem, but no bending of the knee, its driving me nutts. any help is welcome.

thanks
Ian
Quote:
IK or Inverse Kinematics is one of those things that seems really important and special but actually isn’t that important or that special. It is a useful tool for some things if used properly, though. Go Skeleton > IK Handle Tool and pick the top of the dude’s thigh. Then click the joint in the ankle. Maya automatically sets up an IK chain for the leg. If you move the handle thing about the leg follows, but the foot just sticks straight out of the end of the leg. Select the IKhandle THEN the ankle joint. Go Constraint > Orient. Likely as not the foot twists into a stupid position. Unto to get back to where you were. Select the ankle, zoom in on it and go Display > Component Display > Local Rotation axis. You will need to twiddle this thing around so it lines up with the axis of the handle. On the main menu pick the Select by Component Type button and then turn off all the buttons except the question mark (check out the pic below). Select the Local Axis handle and rotate it straight so it lines up with the world – Y up, Z forward and X left. Click on Select by Object Type again and repeat Display > Component Display > Local Rotation axis to hide the thingummy. Constrain the ankle joint to the handle again and it should stay put. Now your leg IK is the same as in lectures 2 and 3 – move the handle around to move the leg and rotate it to rotate the foot. See, that wasn’t so hard.
  Reply with quote
23-01-2005, 09:18 PM   #2
Haro14@msn.com
Registered User
 
Join Date: Jan 2005
Location: MN, USA
Posts: 5
Hi,

Just read the tutorials in the help menu of maya. It explains how to setup the bones and use IK solver and whatnot to make the legs move appropriatly. Its a very good tutorial, and pretty easy to follow, im a beginner at maya and thought it was very easy to follow along.
  Reply with quote
03-04-2006, 02:49 PM   #3
sasskiaduncan
Registered User
 
Join Date: Jan 2006
Location: Great Britain
Posts: 25
hi there
that tutorial seems v familiar - university of bradford perhaps? i'm there too. glad 2 see its not just me who's having difficulty understanding that tutorial!
  Reply with quote
Reply

Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Hoew to duplicate and mirror joints and IK Handles CharlotteKimberly Maya Basics & Newbie Lounge 0 14-02-2018 09:40 AM
resetting IK Handles arran Maya Basics & Newbie Lounge 6 29-09-2006 10:10 AM
ik handles help sasskiaduncan Maya Basics & Newbie Lounge 4 11-04-2006 11:51 PM
IK handles mayakid14 Maya Basics & Newbie Lounge 0 18-01-2005 07:03 AM
Rigid Binding with IK Handles said Animation 3 11-11-2004 03:06 AM