Introduction to Maya - Rendering in Arnold
This course will look at the fundamentals of rendering in Arnold. We'll go through the different light types available, cameras, shaders, Arnold's render settings and finally how to split an image into render passes (AOV's), before we then reassemble it i
# 1 24-02-2004 , 08:08 AM
ctbram's Avatar
Moderator
Join Date: Jan 2004
Location: Michigan, USA
Posts: 2,998

First attempt at a nurb patch human model

The next three shots are of my first attempt at a nurbs patch model.

I started this a while ago but stopped working on it to learn more about the basics of maya. It was really to ambisious a project as my first nurbs model in maya.

The boy is my nephew. I used a digital photos for reference materials.

(1) The first photo is the basic nurbs head mass

(2) The patches I have completed. I stopped because I was not really happy with some of the patches and decided to take a break to rethink how I want to complete it.

(3) The full body so far.

I will probably start with the base nurb head mass and keep the nose patch. I am not happy with the way the eyes were progressing and I will probably scrap them and start over.

Probably scrap the mouth as well. The lips are looking strange and I have not been able to put my finger on it, but I'll figure em out as I get more of the chin and cheek area patched.

The ears are just fast and dirty place holders.

The shirt and pants I modeled from the reference photo.

The shoes, hair and hands are subd's I imported from the sybex master maya book.

Attached Thumbnails

Last edited by ctbram; 24-02-2004 at 08:48 AM.
# 2 24-02-2004 , 08:10 AM
ctbram's Avatar
Moderator
Join Date: Jan 2004
Location: Michigan, USA
Posts: 2,998
(2) The patches so far...

Attached Thumbnails
# 3 24-02-2004 , 08:11 AM
ctbram's Avatar
Moderator
Join Date: Jan 2004
Location: Michigan, USA
Posts: 2,998
(3) the full body ( the nurbs patches just on top of the nurbs head mass)...

Attached Thumbnails
# 4 24-02-2004 , 08:23 AM
ctbram's Avatar
Moderator
Join Date: Jan 2004
Location: Michigan, USA
Posts: 2,998
Oh, and here was my reference photos...

Attached Thumbnails

Last edited by ctbram; 13-03-2004 at 10:42 PM.
# 5 24-02-2004 , 08:44 AM
ctbram's Avatar
Moderator
Join Date: Jan 2004
Location: Michigan, USA
Posts: 2,998
I plopped some hair on him in the full body shot. Here is a upper torso without the hair. You can see it matches the reference pretty well for my first attept.

Attached Thumbnails
# 6 24-02-2004 , 04:16 PM
Kurt's Avatar
Registered User
Join Date: May 2002
Location: Niagara Falls, Canada
Posts: 5,310
Nurbs YUk... very nice model =)


I am enough of an artist to draw freely upon my imagination, knowledge is limited, imagination encircles the world. (Albert Einstein)

https://www.artstation.com/kurtb
# 7 24-02-2004 , 04:18 PM
mtmckinley's Avatar
The Maya Mountain
Join Date: Aug 2002
Location: Seattle, WA
Posts: 8,245
Very nice job. user added image NURBS patch modeling can be very tricky, and it looks like you've gotten the hang of it very well.

# 8 24-02-2004 , 04:53 PM
vladimirjp's Avatar
Subscriber
Join Date: Jun 2003
Location: stuck in the 90's boston, USA
Posts: 1,871
good start. but face needs much more work. nose, eyes, mouth, ears. u should reconsider your curve network setup.


Last edited by vladimirjp; 24-02-2004 at 04:56 PM.
# 9 24-02-2004 , 05:31 PM
ctbram's Avatar
Moderator
Join Date: Jan 2004
Location: Michigan, USA
Posts: 2,998
I am pretty happy with the head mass shape and the nose patch.

The mouth patch is okay but I think it will need to be refined when I get more of the surrounding cheek patches in.

The eye patches will need to be redone. At some point I tried to reduce the geometry and refine the mesh and I lost a ton of detail then I overwrote the file, (newbie lession number 1 - backup to seperate file and backup often!).

The patch network is boluxed and that is why I stoped the model at this point. I intend to come back and finish it but I decided to take a detour and learn more about basic maya modelling with polygons and poly proxies and subd's first.

Jumping into a major human nurbs patch modelling project as ones first forray into maya is probably not the best way to go. The initial massing goes really fast in nurbs but adding detailed patches and then then patch network require a lot of work and pre-planning.

I might redo this project in polygon modelling then use the polygon mesh and draw on surface to build the base nurbs network and then complete the nurbs model.

For me I am thinking nurbs (basic massing) -> poly's/poly proxy for roughing in details and bulding a rough nurbs network -> back to nurb's to complete the model, might be a better way to go. This way I will use the poly model as a wrap deformer and as a starting surface to build my nurbs network from.

This has the added bonus of being able to make a very light poly model that I can then dress in some embarrasing outfit and put into one of the first person shooters. Problem is I have not seen any 3d game that your can added your own models AND skins to yet. user added image

Thanks for the comments.

I am learning all the time and maya is a blast!

Cheersuser added image


Last edited by ctbram; 04-03-2004 at 04:01 PM.
# 10 24-02-2004 , 06:11 PM
ctbram's Avatar
Moderator
Join Date: Jan 2004
Location: Michigan, USA
Posts: 2,998
wireframe on shaded so you can see the current patch network on top of the base nurbs mass.

Attached Thumbnails

Last edited by ctbram; 24-02-2004 at 06:14 PM.
# 11 24-02-2004 , 08:07 PM
dragonsfire's Avatar
Registered User
Join Date: Jan 2003
Location: AB, Canada
Posts: 550
Very Niceuser added image

# 12 25-02-2004 , 01:27 PM
Pixelwelder's Avatar
Registered User
Join Date: Dec 2003
Location: Lisbon
Posts: 71
It´s looking really good, clean smooth detail. user added image

Liked you model, looking forward for the development


weld some pixels !!!
Posting Rules Forum Rules
You may not post new threads | You may not post replies | You may not post attachments | You may not edit your posts | BB code is On | Smilies are On | [IMG] code is On | HTML code is Off

Similar Threads