Introduction to Maya - Modeling Fundamentals Vol 1
This course will look at the fundamentals of modeling in Maya with an emphasis on creating good topology. We'll look at what makes a good model in Maya and why objects are modeled in the way they are.
# 1 09-02-2006 , 08:26 PM
Subscriber
Join Date: Dec 2004
Posts: 203

Making a character to walk from paint a to point b

Hi there all,
I got this project where I need to make a hallway long enough so that my character can walk for 25 seconds, then open a door, and then continue on walking through. However, the problem is that the hallway part is due first and then the character will be due latter. Therefore, I am having problems figuring out how long my hallway should be.

At first, I was thinking of making a dummy character, bone it, and then create a walk cycle which I have done so far. Now I am not sure how I am suppose to make the character to walk from the begining of the path to the door. I did a seach through simplymaya's forums, and the best 2 answers I could find were the following...

1. Try using the motion path. Howevr, nowhere did anyone explained what is suppose to be attached to the curve. So I tried both ways. First I tried attaching the root bone to the curve, but the program said that it couldn't attach the root bone to the curve because the root bone already had a translateX conntected somewhere else. So then, the last thing I tried was attaching the character group node to the curve, which it did attach, but the character didn't move.

2. Then in another thread, someone once said that you would need to make a clip, and then place the clip in the trax editor. In addition, this person also said that he/she only knew very little about using the trax editor, and all he/she could understand about it was from the book called Maya's Fundementals 5. Well, I have this book as well, and I tried watching the video as well as reading the book, but it doesn't explain much about this topic. Basically all it said was that first, you select all your keyable nodes. Next, you create a new clip, and then you will be able to paste that clip onto the trax editor, but that was all it said. However, I still tried do this by following the book's instructions, but the character still walked in place for 25 seconds like he is doing the MC Hammer dance.

So my question is, how do you get a character to walk from point a to point b?

# 2 10-02-2006 , 01:53 PM
Subscriber
Join Date: Dec 2004
Posts: 203
well I found some things on what I was doing wrong. Basically, from watching another tutorial which talks about using Maya's nonlinear animation tools, you are suppose to select all of your keyable animations and then create a new clip. Then you can open the Trax editor, and setup your clips in there and then you will be able to play your animations.

So considering that I found out what I am suppose to do, and because I can't rember which nodes are keyable, is there a way I could see a timeline of all my keys at once?

Also if anyone is currious where this video is, here is the link
https://www.learningmaya.com/index.ph...d=385&search=*

# 3 13-02-2006 , 01:48 PM
Subscriber
Join Date: Dec 2004
Posts: 203
Well, once again, while waiting for a reply, I tried doing what the video shows, and my charater still walks in place. So what gives and what am I doing wrong? I followed exactly to what the video shows. Is it possible that someone could give me an idea how to make the character not to walk in place? Am I suppose to connect the character to a motion path? However, the video doesn't say you need to do this.

Any ideas???

# 4 13-02-2006 , 09:18 PM
Velusion's Avatar
Registered User
Join Date: May 2004
Location: Utah, USA
Posts: 369
The Dope sheet will show all of your keyed attibutes for the character. So will the graph editor.

You could attach the root joint of your skeleton to the path that you set up. I'm not infront of Maya right now but I think you select the joint then select the NURBS curve that is going to be your path then click "make path" or something to that affect. I used paths before and they work well. You can speed them up or slow them down by playing with the length of the path and also by adjusting the curve in the graph editor.

You don't really have to use a path if you don't want to. Assuming that your skeleton is animated walking in place then all you have to do is keyframe the translation of the root join from its start position to its end position. If you don't have the thing walk at the proper rate, the feet will appear to be sliding on the floor so pay attention to that. Good luck.

# 5 14-02-2006 , 12:26 AM
Subscriber
Join Date: Dec 2004
Posts: 203
Thanks Velusion. I will give this a shot later on and let you know how it works out.

Thanks
Bob

Posting Rules Forum Rules
You may not post new threads | You may not post replies | You may not post attachments | You may not edit your posts | BB code is On | Smilies are On | [IMG] code is On | HTML code is Off

Similar Threads