SimplyMaya Forums

Welcome to the forum, feel free to ask questions here.


SM Forums / Lounges / Maya Basics & Newbie Lounge / issues with boolean and smoothing

Maya Basics & Newbie Lounge Please post in this section ONLY if your question doesn't fit in anywhere else on the forum, or if you're not sure which section it's relevant to. We also have Free streaming trial available.

Join the conversation. Reply to post
 
Thread Tools
12-03-2016, 11:41 PM   #1
dmg9626
Registered User
 
Join Date: Mar 2016
Posts: 2
issues with boolean and smoothing
Hi! I'm a new user of Maya, and I had some questions. I'm doing my final project for a 3D modeling course, and I've had some trouble.


I'm modeling a PS3 controller (pictured here).

.


What I have so far consists of the center rectangular base and the cylinders for the two thumbstick bases, which I'm working on right now.

Here's some pictures of what I have so far (both as polygons and smoothed with the 3 key):
The back:






The front (with start/select buttons):






The back (smoothed):



There's some strange pinching going on above the left thumbstick, but I'm not sure if it will pose problems ahead.




The front (smoothed):



As you can see, on the front side of the smoothed model there's some weird edge behavior to the left of the right thumbstick. They don't let me highlight them when I hover over them. It gets more confusing below:


This is what appears when I select a face on the front side of the left thumbstick.
Notice the edges that get selected alongside with it (it seems to think these are the face's bordering edges):






What appears when I try to select an edge on the front side of the left thumbstick:






The edges have especially strange behavior. On the front side of the thumbstick, some edges appear inside a face on the center base of the controller.


This is what happens when I try to select that face:






Again, what I've done so far to get here is construct the rectangular base and the two cylinders, then provide vertices on the base to allow for the cylinder to combine with the base without too complicated geometry. Then I did Boolean > Union, and succeeded in adding the right thumbstick. But when I attempted to add the left thumbstick I had some issues.

First the boolean union was giving me a cylinder with reversed normals. I was selecting the parts in the correct order, but it wasn't working. So I tried reversing the normals of the cylinder before doing the boolean union, and it worked, but left some faces inside the model, so I deleted them and continued to work on making the geometry into quads like I did with the right thumbstick. I thought I had succeeded, but when I checked to see if I had proper edge flow on the cylinder I found the above pictured issues.


Basically what I'm asking is how to get proper edge flow on the front and back faces of the cylinder. I can't think of any other information to provide (sorry if I wrote too much) so I'll attach the scene file if that helps. Thanks in advance!
Attached Files
File Type: zip ps3_v21.zip (35.2 KB, 42 views)

Last edited by dmg9626; 13-03-2016 at 12:02 AM.
  Reply with quote
13-03-2016, 02:50 AM   #2
dmg9626
Registered User
 
Join Date: Mar 2016
Posts: 2
update
Ok so I managed to get edge flow working but I still have those weird little edges inside the face (it moved over to another face on the rectangular base). Here's a screenshot and the scene file:




Ignore the cylinder to the left in the scene, I'm getting ready to add the cylinder that will hold the D-Pad.
Attached Files
File Type: zip ps3_v26.zip (39.8 KB, 37 views)
  Reply with quote
Reply

Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Following a tutorial; Boolean difference makes mesh generate holes? bart95 Maya Modeling 0 22-01-2016 03:29 PM
Smoothing Edges Inkzoid Cartoons Maya Basics & Newbie Lounge 4 12-12-2008 11:19 PM
Smoothing Poly Objects ??? dfp1 Maya Technical Issues 4 16-12-2002 08:11 PM