Geometry type knot(w.i.p)

Introduction to Maya - Modeling Fundamentals Vol 2

This course will look in the fundamentals of modeling in Maya with an emphasis on creating good topology. It's aimed at people that have some modeling experience in Maya but are having trouble with complex objects.

Watch

# 1 25-07-2011 , 03:59 PM

Registered User
Join Date: Aug 2008

Location: U.K.

Posts: 223

When I smooth my hard surfaces found some type of knot, tried merging vertices, tried deling edge that attaches to vertices to re-draw but it wont delete, any ideas

cheers advance

p.s in process of creating a car following a tutorial

Attached Images

Quote

# 2 25-07-2011 , 04:03 PM

Simply Maya OG
Join Date: Dec 2002

Location: Queensbury NY, US A

Posts: 1,438

Going to move this to the proper forum, because there arent any real 'progress' pictures to make it a real WIP thread.

When you merged the verts, what tolerance did you use?

- Hybrid

Quote

# 3 25-07-2011 , 04:49 PM

Registered User
Join Date: Aug 2008

Location: U.K.

Posts: 223

The tolerance is quite high as I merged the vertices around the particular 1's displayed. but still left with the problem user added image

Quote

# 4 25-07-2011 , 04:58 PM

The thin red line
Join Date: Aug 2009

Location: England

Posts: 4,472

I think you will find the problem are the ones I high lighted merge them ..........dave

Attached Images

Avatar Challenge Winner 2010

Quote

# 5 25-07-2011 , 05:30 PM

Registered User
Join Date: Aug 2008

Location: U.K.

Posts: 223

ok will get on it now user added image

fingers crossed

Quote

# 6 25-07-2011 , 06:17 PM

Registered User
Join Date: Aug 2008

Location: U.K.

Posts: 223

it is just this 1 I have left and tried all surrounding vertices but no joy user added image

Attached Images

Quote

# 7 25-07-2011 , 06:34 PM

The thin red line
Join Date: Aug 2009

Location: England

Posts: 4,472

Try again I think could be a lamina face, try deleting the two faces next to the dip then rebuild with append to poly..........dave

Avatar Challenge Winner 2010

Quote

# 8 25-07-2011 , 06:44 PM

Moderator
Join Date: Jan 2004

Location: Michigan, USA

Posts: 2,998

It is more likely you have a internal face in this intance. You can use the mesh>cleanup tools to find and correct the problem.

A manual way to fix this is to delete the face(s) in the affected area, look for internal faces, if you see none then rebuild the faces using append to poly, extrude edge and merge verts, and bridge tools in whatever combination you need.

"If I have seen further it is by standing on the shoulders of giants." Sir Isaac Newton, 1675

Last edited by ctbram; 25-07-2011 at 06:56 PM.

Quote

# 9 25-07-2011 , 08:49 PM

Registered User
Join Date: Aug 2008

Location: U.K.

Posts: 223

cheeers guys will try it shortly user added image

Thanks for the response so swiftly user added image

Quote

# 10 25-07-2011 , 11:17 PM

Lifetime Member
Join Date: Feb 2010

Location: Australia

Posts: 4,255

Im with ct and dave silverspawn....sometimes there isnt anything wrong at all...I have had this before too...dont know why Maya does it but sometimes she gets cranky..I delete faces one by one in the area and rebuild too...works usually

cheers bullet

bullet1968

"A Darkness at Sethanon", a book I aspire to model some of the charcters and scenes

Quote