Introduction to Maya - Modeling Fundamentals Vol 1
This course will look at the fundamentals of modeling in Maya with an emphasis on creating good topology. We'll look at what makes a good model in Maya and why objects are modeled in the way they are.
# 1 16-10-2004 , 04:03 AM
Velusion's Avatar
Registered User
Join Date: May 2004
Location: Utah, USA
Posts: 369

MR hates my model

I did a model of a T-rex using a NURBS to Poly to SubD technique. I made sure that I had NO 5 sided faces. The model is made up of 4 and 3 sided faces. It renders fine with Mayas software renderer but Mental Ray won't touch it. I know the problem has to do with the triangles in my poly model. Once I convert the model to SubD and switch to subdivision level 0 I can see that many of the faces seem disconnected from the rest. I ran a simple test. I took a poly cube and converted it to subD then rendered it with Mental Ray. Everything worked as expected. Next, I took a poly cube and spit one of the faces so that it was now 2 triangles. I converted it to SubD then examined it at subD level O. Just like with my T-rex model, the SubD cube had disconnected faces on the side where I split the quad into 2 triangles. The triangles are causing the problem. When I would try to render a subD that was made by converting a poly with triangles, Mental ray would cause Maya to generate this error: "non-quadrilateral face in base mesh not supported."

Question: Is there anything I can do about this besides trying to find every single triangle in my poly T-rex and eliminating them?

I have tried to use Quadrangulate but it didn't help. I don't want to use a dense poly model for my project but if I can't get the subD to render in Mental Ray then I'm going to have to.

By the way, Here is a link to my site incase you want to see the T-rex that is causing me all this trouble. Morphic Motion

# 2 16-10-2004 , 04:37 AM
NitroLiq's Avatar
Moderator
Join Date: Nov 2002
Location: New York
Posts: 2,133
Maybe quadchecker will help you out. Check this thread.


"Terminat Bora Diem, Terminal Auctor opus."
# 3 16-10-2004 , 04:44 AM
Pony's Avatar
Subscriber
Join Date: Mar 2003
Location: with PonysGirl
Posts: 2,573
It is possible not to have to work out the triangles.


Subdiv Surfaces > Collapse Hierarchy
this will give you higher mesh. BUT you can keep your triangle count down in renders, buy lowering the Tessellation, sample count of 2 should get you close to the original count.

There will be a Higher mesh to deal with. could slow down interactivity for animation. But this is something that would be done right before renders anyway.

# 4 16-10-2004 , 04:57 PM
Velusion's Avatar
Registered User
Join Date: May 2004
Location: Utah, USA
Posts: 369
Nitroliq, I will check out the link that you provided. Thanks

Pony, Your solution did the trick!! I am so freakin happy:p I will have to read through some of my books to see just exactly what collapsing the hierarchy did but for right now, I'm just thrilled that it worked.

Thanks again..

# 5 17-10-2004 , 03:30 AM
Velusion's Avatar
Registered User
Join Date: May 2004
Location: Utah, USA
Posts: 369
Well, everything seemed good until I tried to apply a map to the model. First I applied it to the subD model before collapsing the hierarchy but after the collapse, the map was messed up. I guess because of the UV mapping created when doing the collapse. then I tried to create a simple camera view projection UV map from the collapsed model but that pretty much froze up my computer every time I tried.

Unless someone has a better idea, I'm just going to do this:
1 low poly model
2. convert to subd
3 convert subd back to poly using adaptive setting
4 create my UV maps from converted model
5 right before rendering, I'll apply poly smooth to the model but not to the UVs.
6 render smoothed poly model with mental ray.

One more thing: How do you pull up a report that tells you how many polys are in your model?

# 6 05-11-2004 , 09:37 AM
ereitz's Avatar
Subscriber
Join Date: Dec 2002
Location: Germany/Canada
Posts: 545
hi Velusion - I've been importing models into zbrush where you also need quad polys exlusively and i found poly cleanup worked but not by repairing - rather check the option to select non-quad polygons.

I also found my poly count dissappeared with maya 6 (headsup display/polycount) but it returned when I installed the update to 6.01.

Good luck user added image


Check out the subsurfacescattering on my tongue...

<a href="https://www.reitzmachine.com">www.reitzmachine.com</a>
Posting Rules Forum Rules
You may not post new threads | You may not post replies | You may not post attachments | You may not edit your posts | BB code is On | Smilies are On | [IMG] code is On | HTML code is Off

Similar Threads