Maya 2020 fundamentals - modelling the real world
Get halfway through a model and find it's an unworkable mess? Can't add edge loops where you need them? Can't subdivide a mesh properly? If any of this sounds familiar check this course out.
# 1 30-11-2004 , 03:42 PM
Mad_Majd's Avatar
Registered User
Join Date: Nov 2004
Location: Jordan
Posts: 6

plz help about surface planar

hi guys , this is my first try to post at this lovelly forum ,
so pllllz help me .
i'm trying to model a mobile phone , but i don't know how to close the face surface of the phone . sorry for my bad English .
i tryied to make planar eith the last surface curve, it doesn't work .

thx for help

Attached Thumbnails

MaD MajD
# 2 30-11-2004 , 03:54 PM
blomkaal's Avatar
Subscriber
Join Date: May 2004
Location: Denmark
Posts: 816
I don't really know that much about nurbs, but I'm think a curve has to be planar to make a planar surface... Hence the name user added image

As I said I don't know much about nurbs, so I'd probably advise you to convert to polys, add faces to close the hole and then convert to sub-d's or smooth the polys... I can't remember the convert settings, but Kurt goes over the process in the free cartoon dog tut...

-Blomkaal

# 3 01-12-2004 , 07:36 PM
Mad_Majd's Avatar
Registered User
Join Date: Nov 2004
Location: Jordan
Posts: 6
thx for help dude , but it doesn't work . . i tryed to close it with poly surface but it still not fit well . . i think there is a suprem way to do that with nurbs , but seems no body wana help
pllllllllllllz help i'v to finish it & i didn't start yet !! user added image :bored: :bored: :bored:


MaD MajD
# 4 01-12-2004 , 07:52 PM
ckyuk's Avatar
Subscriber
Join Date: Apr 2003
Location: Great Britain
Posts: 1,336
i'd spit the curve at the corners and use a birail operation. However i'm the same as blomkaal, i don't really know much about nurbs as i try and stay away from them, more of a polys -> subd person. Sorry

# 5 02-12-2004 , 05:51 PM
Mad_Majd's Avatar
Registered User
Join Date: Nov 2004
Location: Jordan
Posts: 6
thx alot guys ,, unless u post user added image

but still i wish to solve this trick ... plz help


MaD MajD
# 6 03-12-2004 , 02:08 AM
yingying's Avatar
Registered User
Join Date: Nov 2004
Location: far far away...
Posts: 13
How about cut this curve into four part, and use Surfaces -> Birail 2 tool to build a nurb face?


someone say bye, someone say hi
some may forget you, but never would i...
# 7 03-12-2004 , 05:37 AM
MainlineX's Avatar
Registered User
Join Date: Jun 2003
Location: Johannesburg
Posts: 641
Hey Mad_Majd....How about you split the curve in the center so that you end up with two curves and then loft between those curves and then rebuild the surface it creates and then curve snap or point snap the points on that surface so that it sits nicely with the rest of the surface...thats How I would go about doing it....user added image Hope it helps you out....user added imageuser added image



-------------------------------------------
# 8 03-12-2004 , 01:07 PM
Mad_Majd's Avatar
Registered User
Join Date: Nov 2004
Location: Jordan
Posts: 6
hi again , thx for u both YingYing & MainlineX for ur help ,
i triyed to do what u told me MainlineX but it still need something to do about it , the surface which reduced after plabar had a semetry hole at the middle , can u plz help me with that ,
thx alot and sorry for my bad English again .

Attached Images

MaD MajD
# 9 03-12-2004 , 01:37 PM
ckyuk's Avatar
Subscriber
Join Date: Apr 2003
Location: Great Britain
Posts: 1,336
EDIT: - File didn't upload for some reason, so this post wouldn't make sence.

# 10 03-12-2004 , 03:43 PM
Mad_Majd's Avatar
Registered User
Join Date: Nov 2004
Location: Jordan
Posts: 6
sory but what i understod from u that my last file had some upload problem . so i'll post it again with this thread .

Attached Images

MaD MajD
Posting Rules Forum Rules
You may not post new threads | You may not post replies | You may not post attachments | You may not edit your posts | BB code is On | Smilies are On | [IMG] code is On | HTML code is Off

Similar Threads