Introduction to Maya - Modeling Fundamentals Vol 2
This course will look in the fundamentals of modeling in Maya with an emphasis on creating good topology. It's aimed at people that have some modeling experience in Maya but are having trouble with complex objects.
# 1 19-08-2003 , 01:47 AM
Emo's Avatar
Subscriber
Join Date: Jul 2002
Location: MELville
Posts: 1,100

What is pushing the limits?

Hey everybody...

Since I decided I dont want a new car I have all this money to spend so I've started on a "big" project....:bgreen:

I've started building my Workstation for Maya so I was wondering what would you guys consider as to what is pushing it when it comes to the hardware that is used?

I mean, do I REALLY need the best of the best of the best of the best? I mean, I've started buying all the stuff and right now I dont care as to how much they are... (Hell, I've spend $500 on my Mobo alone) so as you can see, I've made this big project for me already

One question that i have is about HDDs.... Somebody told me about RAID SCSI setups but like I said before, would I really need that?

Thanks

-Emo

# 2 19-08-2003 , 02:48 AM
carrot juice's Avatar
Registered User
Join Date: Mar 2003
Location: San Antonio, TX
Posts: 346
If you really have no limits in mind, and your mobo has 2 AGP ports, I would get a Wildcat VP990 Pro 512MB in one slot and a nVidia Quadro FX 2000 in the other- the first for that crazy RAM, the second for hardware rendering. That would be sweet! :p

# 3 19-08-2003 , 05:13 PM
cujo's Avatar
Registered User
Join Date: Jul 2003
Posts: 51
i usually see raids on avid setups.

You could just get a good quality hard drive
( the hard drive is the oldest technology in a computer,
and the average life is only 5 years ) and all it would do
is load/save your files a little faster.
Save your $$$ for a kick ass Video card like carrot juice said,
( just the wildcat would be more than enough-),
a dvd burner and as much of the fastest ram you can stuff in there.
avoid amd chips ( unless the mb you got is for them -if so sorry)
get the fastest processer(s) you can. when you render a 1000
fram raytraced animation you'll thank me.
I've rendered some high res stuff for print that takes all night for one frame.
and if you have any $$ left over, send it to me. I need a car.
just kidding
Joe


rasterfarian
# 4 19-08-2003 , 08:04 PM
Emo's Avatar
Subscriber
Join Date: Jul 2002
Location: MELville
Posts: 1,100
hahah... thanks guys...

Carrot Juice, yeah, that'd be sweet but believe me, at the time I ordered my Mobo, sites like [H]ardOC were speculating that these kinds of Mobos dont exist with a AGP slot all together so I dont think I"ll find a mobo with dual AGP slots... user added image

and Cujo, why should I stay away from AMD chips?

Last night I ordered my RAM (for now I just got 1GB (2x512) PC3200 DDR ECC ram) ..later I might make that 2GB...

-Emo

# 5 20-08-2003 , 12:33 AM
cujo's Avatar
Registered User
Join Date: Jul 2003
Posts: 51
https://www.3dchips.net/content/review.php?id=63&page=1
check out the link from the other post.

all the personal experience i've had with amd's have been nothing but problems.
I've never had any problems with pentium.

The main problem I had was over heating till it froze up.
just running the temp diagnostic program caused them to overheat.
So I took the box back to the place that I bought it from.
They added an orbital fan- Still over heated
I cut holes in my desk to increase air flow- Still over heated
They finally replace the chip-The new one over heated
Then they replaced the chip again and the motherboard
Still over heated.
Then They replaced with a new mother board with an intel
chip- never had a problem since.
While I was having the probs I searched the net
and found lots of complaints/articles of over heating, locking up etc. on amd's.

I worked at another place that used amd's- (surprise) they overheated

I suspect they are cheaper chips for a reason.

I'm no chip expert, but
I've never had, or heard of, or worked anywhere, that had a
problem with pentiums or xeons.

After all the crap I went through- I would never ever buy another amd product again. It would'nt be worth the hassel to save a few $$$- Just my opinion though.
I'm sure if someone had the same problems with intels
they'd feel the same about them.
Joe


rasterfarian
# 6 20-08-2003 , 12:46 AM
Zyk0tiK's Avatar
Registered User
Join Date: Aug 2003
Posts: 800
lol if you're going ALL OUT on a computer get a new Mac G4 done up to the shit. god damn, if you got 14k to spend on the computer alone you'll be FLYING mate user added image

# 7 20-08-2003 , 01:54 AM
Emo's Avatar
Subscriber
Join Date: Jul 2002
Location: MELville
Posts: 1,100
cujo... thanks for the link and your suggestion but I'm kinda of a die hard AMD fan and I already bought the AMD board so I can't switch even if I wanted to (witch I dont)

AMDs overheat, that's true, but that doesn't mean they are bad. it's just a matter of personal preference I guess when it comes down to Intel/AMD

and Zyk0tiK, sorry but I would NEVER EVER EVER spend 14K on a PC...let alone a MAC...lol

-Emo

# 8 20-08-2003 , 04:40 PM
cujo's Avatar
Registered User
Join Date: Jul 2003
Posts: 51
"AMDs overheat, that's true, but that doesn't mean they are bad."
huh?

I equate it with having a one night stand without a condom.
It's possible that she's a virgin. but why chance it.

Well ya know what they say about opinions.
....I'm sure mine is no better.

anyway..... save often.

at least your not wastin' $$$ on a mac. lol.
Joe


rasterfarian
Posting Rules Forum Rules
You may not post new threads | You may not post replies | You may not post attachments | You may not edit your posts | BB code is On | Smilies are On | [IMG] code is On | HTML code is Off

Similar Threads